Contents

8×63mm patron m/32

Bottlenecked centerfire cartridge

8×63mm
Two 8×63mm patron m/32 military cartridges
Type	Rifle
Place of origin	Sweden
Service history
In service	1932–1975
Used by	Sweden
Wars	UN intervention in Kongo 1960-1964
Production history
Designer	Kungliga Armétygförvaltningen (KAF) AktieBolaget Bofors
Designed	1927–1932
Manufacturer	AB Bofors
Specifications
Case type	Rebated, bottleneck
Bullet diameter	8.20 mm (0.323 in)
Neck diameter	9.10 mm (0.358 in)
Shoulder diameter	11.51 mm (0.453 in)
Base diameter	12.43 mm (0.489 in)
Rim diameter	12.18 mm (0.480 in)
Rim thickness	1.42 mm (0.056 in)
Case length	62.81 mm (2.473 in)
Overall length	84.62 mm (3.331 in)
Primer type	Berdan, Large rifle
Ballistic performance
Bullet mass/type Velocity Energy 14.2 g (219 gr) m/32 FMJ 760 m/s (2,500 ft/s) 4,101 J (3,025 ft⋅lbf)
Test barrel length: 609 mm (24 in) Source(s): [1]

The 8×63mm patron m/32 was a bottlenecked centrefire cartridge with a slightly (0.25 mm (0.0098 in)) rebated rim for Swedish heavy and medium machine guns. It was used from 1932 to the finalisation of the re-chambering process of these machine guns to 7.62×51mm NATO in 1975.

Given the experiences of the devastating effect of small arms fire, including the long-range, even indirect fire of the machine guns, in the Russo-Japanese War and World War I, as well as a revolution in terminal ballistic calculations, calibre-related concerns occupied a lot of attention worldwide in military establishments.^[2] Sweden was no exception, and series of trials in calibres 6mm-12mm were conducted until the late 1920s.^[2] At this time, the standard service cartridge in Swedish use was the 6.5×55mm Swedish skarp patron m/94 projektil m/94 (live cartridge m/94 projectile m/94) service ammunition loaded with a 10.1 grams (156 gr) long round-nosed m/94 (B-projectile) bullet. After study-travels by Lieutenant Colonel de Laval along with Captains Nygren and Holmgren, mainly to Germany and the Netherlands in October 1930, Royal Swedish Army Materiel Administration (Kungliga Armétygförvaltningen (KAF) appointed a commission that conducted a series of tests with calibres 6,5 mm to 7,2 – 7,5 – 7,9 mm, and bullet weights between 8.4 grams and 17.0 grams, with the intention to either recommend a new calibre for the kulspruta m14-29 or retain the 6.5×55mm but with a new boat tailed spitzer bullet, as the old blunt nosed projectile m/94 had inferior ballistics.^[2] The commission found that at ranges below 2,400 m (2,625 yd), no recommendation could be given without indepth analysis of intended tasks within the tactical doctrine.^[2] Past this, the 14.2 gram bullet in calibre 7.9mm had superior performance in precision and penetration while not causing excessive barrel wear as well as fulfilling the requirement of 20 kilogram-metres impact force up to a range of 3,600 m (3,937 yd).^[2] Based on this, KAF tasked AB Bofors to develop and manufacture the larger rifle cartridge to meet these needs.^[2]

The patron m/32 round had the same overall length as the .30-06 Springfield cartridge, which allowed it to fit in the standard Browning receiver, but used a larger diameter case and share the 6.5×55mm 12.2 mm (0.48 in) diameter bolt face. Compared to the 1928 pattern .30-06 Springfield M1 Ball the 8×63mm patron m/32 was loaded with 8.20 mm (0.323 in) S bore 14.2 g (219.1 gr) bullets and had more muzzle energy. The 8×63mm patron m/32 had a muzzle velocity of 760 m/s (2,493 ft/s) and an operating pressure of 330 MPa (47,862 psi).

The patron m/32's aerodynamically refined boat tailed spitzer bullet had a useful range of approximately 3,600 m (3,937 yd) on which the impact energy was 20 kilogram-meters (196 J / 145 ft⋅lbf),^[3][4] and a maximum range of approximately 5,500 m (6,015 yd) when fired from a kulspruta m/36.^[5] Reverse engineering the trajectory from the previous sentence indicates a ballistic coefficient (G1 BC) of approximately 0.63. Available with armour piercing bullets, patron m/32 was used in the UN-forces' KP-bil during the Congo-crisis against the separatists' armoured cars.

The 8×63mm patron m/32 cartridge was used in the following machine guns:^[6]

• Kulspruta m/14-29
• Flygplanskulspruta m/22
• Kulspruta m/36
• Kulspruta m/39
• Kulspruta m/42

The 8×63mm patron m/32 was also used in the gevär / pansarvärnsgevär m/40^[2] bolt-action rifle, Karabiner 98k's re-chambered in Sweden for the patron m/32. Originally purchased as the pvg m/39in8×57 IS as a stop-gap anti-tank rifle (despite being unsuited for the role), the re-chambered 8×63 rifles were designated m/40, and later issued to machine gun crews so their rifles would fire the same round as their machine guns. Besides the rechambering a muzzle brake was added necessitated by the additional recoil produced by the more powerful 8×63mm patron m/32 cartridge.

The operating pressures of the various ammunition types varied between 330–350 MPa (47,862–50,763 psi).

• List of Swedish military calibres
• List of rebated rim cartridges
• 8 mm caliber

Wikimedia Commons has media related to 8 x 63 mm m/32.

• 8x63 M32 Bofors
• HISTORIC MACHINE GUN CARTRIDGES by Anthony G Williams Archived 2022-03-03 at the Wayback Machine
• 8x63 Swedish / 8x63 Bofors (in Russian)
• 8x63 Swedish Bofors / 8 mm Bofors / 8x63 Swedish For MG Mod.1932 / 8mm SK PTR M-32 / 8mm Sueco / 8x63 / SAA 4540 / XCR 08 063 BGC 010 (In Spanish)
• The Swedish military ammunition site
• Ammunitionsregister för armén, 1960
• instruction drawings of 8×63mm patron m/32 ammunition
• Military Small Arms Ammunition of the World, 1945-1980, P. Labbett