Iridium

A member of the platinum group metals, iridium is white, resembling platinum, but with a slight yellowish cast. Because of its hardness, brittleness, and very high melting point, solid iridium is difficult to machine, form, or work; thus powder metallurgy is commonly employed instead.^[15] It is the only metal to maintain good mechanical properties in air at temperatures above 1,600 °C (2,910 °F).^[16] It has the 10th highest boiling point among all elements and becomes a superconductor at temperatures below 0.14 K (−273.010 °C; −459.418 °F).^[17]

Iridium's modulus of elasticity is the second-highest among the metals, being surpassed only by osmium.^[16] This, together with a high shear modulus and a very low figure for Poisson's ratio (the relationship of longitudinal to lateral strain), indicate the high degree of stiffness and resistance to deformation that have rendered its fabrication into useful components a matter of great difficulty. Despite these limitations and iridium's high cost, a number of applications have developed where mechanical strength is an essential factor in some of the extremely severe conditions encountered in modern technology.^[16]

The measured density of iridium is only slightly lower (by about 0.12%) than that of osmium, the densest metal known.^[18][19] Some ambiguity occurred regarding which of the two elements was denser, due to the small size of the difference in density and difficulties in measuring it accurately,^[20] but, with increased accuracy in factors used for calculating density, X-ray crystallographic data yielded densities of 22.56 g/cm³ (0.815 lb/cu in) for iridium and 22.59 g/cm³ (0.816 lb/cu in) for osmium.^[21]

Iridium is extremely brittle, to the point of being hard to weld because the heat-affected zone cracks, but it can be made more ductile by addition of small quantities of titanium and zirconium (0.2% of each apparently works well).^[22]

The Vickers hardness of pure platinum is 56 HV, whereas platinum with 50% of iridium can reach over 500 HV.^[23][24]

Iridium is the most corrosion-resistant metal known.^[25] It is not attacked by acids, including aqua regia, but it can be dissolved in concentrated hydrochloric acid in the presence of sodium perchlorate.^[12] In the presence of oxygen, it reacts with cyanide salts.^[26] Traditional oxidants also react, including the halogens and oxygen^[27] at higher temperatures.^[28] Iridium also reacts directly with sulfur at atmospheric pressure to yield iridium disulfide.^[29]

Iridium has two naturally occurring stable isotopes, ¹⁹¹Ir and ¹⁹³Ir, with natural abundances of 37.3% and 62.7%, respectively.^[30] At least 37 radioisotopes have also been synthesized, ranging in mass number from 164 to 202. ¹⁹²Ir, which falls between the two stable isotopes, is the most stable radioisotope, with a half-life of 73.827 days, and finds application in brachytherapy^[31] and in industrial radiography, particularly for nondestructive testing of welds in steel in the oil and gas industries; iridium-192 sources have been involved in a number of radiological accidents. Three other isotopes have half-lives of at least a day—¹⁸⁸Ir, ¹⁸⁹Ir, and ¹⁹⁰Ir.^[30] Isotopes with masses below 191 decay by some combination of β⁺ decay, α decay, and (rare) proton emission, with the exception of ¹⁸⁹Ir, which decays by electron capture. Synthetic isotopes heavier than 191 decay by β⁻ decay, although ¹⁹²Ir also has a minor electron capture decay path.^[30] All known isotopes of iridium were discovered between 1934 and 2008, with the most recent discoveries being ^200–202Ir.^[32]

At least 32 metastable isomers have been characterized, ranging in mass number from 164 to 197. The most stable of these is ^192m2Ir, which decays by isomeric transition with a half-life of 241 years,^[30] making it more stable than any of iridium's synthetic isotopes in their ground states. The least stable isomer is ^190m3Ir with a half-life of only 2 μs.^[30] The isotope ¹⁹¹Ir was the first one of any element to be shown to present a Mössbauer effect. This renders it useful for Mössbauer spectroscopy for research in physics, chemistry, biochemistry, metallurgy, and mineralogy.^[33]

[Ir(CO)
₃]³⁻

[Ir(CO)₃(PPh₃)]¹⁻

Ir₄(CO)₁₂

[IrCl(CO)(PPh₃)₂]

Ir(C₅H₅)₂

IrCl₃

IrO₂

Ir₄F₂₀

IrF
₆

[Ir(O₂)O₂]⁺

IrO₄

[IrO₄]^+[4]

Iridium forms compounds in oxidation states between −3 and +9, but the most common oxidation states are +1, +2, +3, and +4.^[15] Well-characterized compounds containing iridium in the +6 oxidation state include IrF₆ and the oxides Sr₂MgIrO₆ and Sr₂CaIrO₆.^[15][34] iridium(VIII) oxide (IrO₄) was generated under matrix isolation conditions at 6 K in argon.^[35] The highest oxidation state (+9), which is also the highest recorded for any element, is found in gaseous [IrO₄]⁺.^[4]

Iridium does not form binary hydrides. Only one binary oxide is well-characterized: iridium dioxide, IrO
₂. It is a blue black solid that adopts the fluorite structure.^[15]Asesquioxide, Ir
₂O
₃, has been described as a blue-black powder, which is oxidized to IrO
₂byHNO
₃.^[27] The corresponding disulfides, diselenides, sesquisulfides, and sesquiselenides are known, as well as IrS
₃.^[15]

Binary trihalides, IrX
₃, are known for all of the halogens.^[15] For oxidation states +4 and above, only the tetrafluoride, pentafluoride and hexafluoride are known.^[15] Iridium hexafluoride, IrF
₆, is a volatile yellow solid, composed of octahedral molecules. It decomposes in water and is reduced to IrF
₄.^[15] Iridium pentafluoride is also a strong oxidant, but it is a tetramer, Ir
₄F
₂₀, formed by four corner-sharing octahedra.^[15]

Iridium has extensive coordination chemistry.

Iridium in its complexes is always low-spin. Ir(III) and Ir(IV) generally form octahedral complexes.^[15] Polyhydride complexes are known for the +5 and +3 oxidation states.^[36] One example is IrH₅(PⁱPr₃)₂.^[37] The ternary hydride Mg
₆Ir
₂H
₁₁ is believed to contain both the IrH⁴⁻
₅ and the 18-electron IrH⁵⁻
₄ anion.^[38]

Iridium also forms oxyanions with oxidation states +4 and +5. K
₂IrO
₃ and KIrO
₃ can be prepared from the reaction of potassium oxideorpotassium superoxide with iridium at high temperatures. Such solids are not soluble in conventional solvents.^[39]

Just like many elements, iridium forms important chloride complexes. Hexachloroiridic (IV) acid, H
₂IrCl
₆, and its ammonium salt are the most common iridium compounds from both industrial and preparative perspectives.^[40] They are intermediates in the purification of iridium and used as precursors for most other iridium compounds, as well as in the preparation of anode coatings. The IrCl²⁻
₆ ion has an intense dark brown color, and can be readily reduced to the lighter-colored IrCl³⁻
₆ and vice versa.^[40] Iridium trichloride, IrCl
₃, which can be obtained in anhydrous form from direct oxidation of iridium powder by chlorine at 650 °C,^[40] or in hydrated form by dissolving Ir
₂O
₃inhydrochloric acid, is often used as a starting material for the synthesis of other Ir(III) compounds.^[15] Another compound used as a starting material is ammonium hexachloroiridate(III), (NH
₄)
₃IrCl
₆.^{[citation needed]}

In the presence of air, iridium metal dissolves in molten alkali-metal cyanides to produce the Ir(CN)³⁻
₆ (hexacyanoiridate) ion and upon oxidation produces the most stable oxide.^{[citation needed]}

Organoiridium compounds contain iridium–carbon bonds. Early studies identified the very stable tetrairidium dodecacarbonyl, Ir
₄(CO)
₁₂.^[15] In this compound, each of the iridium atoms is bonded to the other three, forming a tetrahedral cluster. The discovery of Vaska's complex (IrCl(CO)[P(C
₆H
₅)
₃]
₂) opened the door for oxidative addition reactions, a process fundamental to useful reactions. For example, Crabtree's catalyst, a homogeneous catalyst for hydrogenation reactions.^[41][42]

Iridium complexes played a pivotal role in the development of Carbon–hydrogen bond activation (C–H activation), which promises to allow functionalization of hydrocarbons, which are traditionally regarded as unreactive.^[45]

The discovery of iridium is intertwined with that of platinum and the other metals of the platinum group. The first European reference to platinum appears in 1557 in the writings of the Italian humanist Julius Caesar Scaliger as a description of an unknown noble metal found between Darién and Mexico, "which no fire nor any Spanish artifice has yet been able to liquefy".^[46] From their first encounters with platinum, the Spanish generally saw the metal as a kind of impurity in gold, and it was treated as such. It was often simply thrown away, and there was an official decree forbidding the adulteration of gold with platinum impurities.^[47]

In 1735, Antonio de Ulloa and Jorge Juan y Santacilia saw Native Americans mining platinum while the Spaniards were travelling through Colombia and Peru for eight years. Ulloa and Juan found mines with the whitish metal nuggets and took them home to Spain. Ulloa returned to Spain and established the first mineralogy lab in Spain and was the first to systematically study platinum, which was in 1748. His historical account of the expedition included a description of platinum as being neither separable nor calcinable. Ulloa also anticipated the discovery of platinum mines. After publishing the report in 1748, Ulloa did not continue to investigate the new metal. In 1758, he was sent to superintend mercury mining operations in Huancavelica.^[46]

In 1741, Charles Wood,^[48] a British metallurgist, found various samples of Colombian platinum in Jamaica, which he sent to William Brownrigg for further investigation.

In 1750, after studying the platinum sent to him by Wood, Brownrigg presented a detailed account of the metal to the Royal Society, stating that he had seen no mention of it in any previous accounts of known minerals.^[49] Brownrigg also made note of platinum's extremely high melting point and refractory metal-like behaviour toward borax. Other chemists across Europe soon began studying platinum, including Andreas Sigismund Marggraf,^[50] Torbern Bergman, Jöns Jakob Berzelius, William Lewis, and Pierre Macquer. In 1752, Henrik Scheffer published a detailed scientific description of the metal, which he referred to as "white gold", including an account of how he succeeded in fusing platinum ore with the aid of arsenic. Scheffer described platinum as being less pliable than gold, but with similar resistance to corrosion.^[46]

Chemists who studied platinum dissolved it in aqua regia (a mixture of hydrochloric and nitric acids) to create soluble salts. They always observed a small amount of a dark, insoluble residue.^[16] Joseph Louis Proust thought that the residue was graphite.^[16] The French chemists Victor Collet-Descotils, Antoine François, comte de Fourcroy, and Louis Nicolas Vauquelin also observed the black residue in 1803, but did not obtain enough for further experiments.^[16]

In 1803 British scientist Smithson Tennant (1761–1815) analyzed the insoluble residue and concluded that it must contain a new metal. Vauquelin treated the powder alternately with alkali and acids^[25] and obtained a volatile new oxide, which he believed to be of this new metal—which he named ptene, from the Greek word πτηνός ptēnós, "winged".^[51][52] Tennant, who had the advantage of a much greater amount of residue, continued his research and identified the two previously undiscovered elements in the black residue, iridium and osmium.^[16][25] He obtained dark red crystals (probably of Na
₂[IrCl
₆]·nH
₂O) by a sequence of reactions with sodium hydroxide and hydrochloric acid.^[52] He named iridium after Iris (Ἶρις), the Greek winged goddess of the rainbow and the messenger of the Olympian gods, because many of the salts he obtained were strongly colored.^[c][53] Discovery of the new elements was documented in a letter to the Royal Society on June 21, 1804.^[16][54]

British scientist John George Children was the first to melt a sample of iridium in 1813 with the aid of "the greatest galvanic battery that has ever been constructed" (at that time).^[16] The first to obtain high-purity iridium was Robert Hare in 1842. He found it had a density of around 21.8 g/cm³ (0.79 lb/cu in) and noted the metal is nearly immalleable and very hard. The first melting in appreciable quantity was done by Henri Sainte-Claire Deville and Jules Henri Debray in 1860. They required burning more than 300 litres (79 US gal) of pure O
₂ and H
₂ gas for each 1 kilogram (2.2 lb) of iridium.^[16]

These extreme difficulties in melting the metal limited the possibilities for handling iridium. John Isaac Hawkins was looking to obtain a fine and hard point for fountain pen nibs, and in 1834 managed to create an iridium-pointed gold pen. In 1880, John Holland and William Lofland Dudley were able to melt iridium by adding phosphorus and patented the process in the United States; British company Johnson Matthey later stated they had been using a similar process since 1837 and had already presented fused iridium at a number of World Fairs.^[16] The first use of an alloy of iridium with rutheniuminthermocouples was made by Otto Feussner in 1933. These allowed for the measurement of high temperatures in air up to 2,000 °C (3,630 °F).^[16]

InMunich, Germany in 1957 Rudolf Mössbauer, in what has been called one of the "landmark experiments in twentieth-century physics",^[55] discovered the resonant and recoil-free emission and absorption of gamma raysbyatoms in a solid metal sample containing only ¹⁹¹Ir.^[56] This phenomenon, known as the Mössbauer effect resulted in the awarding of the Nobel Prize in Physics in 1961, at the age 32, just three years after he published his discovery.^[57]

Along with many elements having atomic weights higher than that of iron, iridium is only naturally formed by the r-process (rapid neutron capture) in neutron star mergers and possibly rare types of supernovae.^[58][59][60]

Iridium is one of the nine least abundant stable elementsinEarth's crust, having an average mass fraction of 0.001 ppm in crustal rock; platinum is 10 times more abundant, gold is 40 times more abundant, silver and mercury are 80 times more abundant.^[15] Tellurium is about as abundant as iridium.^[15] In contrast to its low abundance in crustal rock, iridium is relatively common in meteorites, with concentrations of 0.5 ppm or more.^[62] The overall concentration of iridium on Earth is thought to be much higher than what is observed in crustal rocks, but because of the density and siderophilic ("iron-loving") character of iridium, it descended below the crust and into Earth's core when the planet was still molten.^[40]

Iridium is found in nature as an uncombined element or in natural alloys, especially the iridium–osmium alloys osmiridium (osmium-rich) and iridosmium (iridium-rich).^[25]Innickel and copper deposits, the platinum group metals occur as sulfides, tellurides, antimonides, and arsenides. In all of these compounds, platinum can be exchanged with a small amount of iridium or osmium. As with all of the platinum group metals, iridium can be found naturally in alloys with raw nickel or raw copper.^[63] A number of iridium-dominant minerals, with iridium as the species-forming element, are known. They are exceedingly rare and often represent the iridium analogues of the above-given ones. The examples are irarsite and cuproiridsite, to mention some.^[64][65][66] Within Earth's crust, iridium is found at highest concentrations in three types of geologic structure: igneous deposits (crustal intrusions from below), impact craters, and deposits reworked from one of the former structures. The largest known primary reserves are in the Bushveld igneous complex in South Africa,^[67] (near the largest known impact structure, the Vredefort impact structure) though the large copper–nickel deposits near Norilsk in Russia, and the Sudbury Basin (also an impact crater) in Canada are also significant sources of iridium. Smaller reserves are found in the United States.^[67] Iridium is also found in secondary deposits, combined with platinum and other platinum group metals in alluvial deposits. The alluvial deposits used by pre-Columbian people in the Chocó DepartmentofColombia are still a source for platinum-group metals. As of 2003, world reserves have not been estimated.^[25]

Iridium is found within marine organisms, sediments, and the water column. The abundance of iridium in seawater^[68] and organisms^[69] is relatively low, as it does not readily form chloride complexes.^[69] The abundance in organisms is about 20 parts per trillion, or about five orders of magnitude less than in sedimentary rocks at the Cretaceous–Paleogene (K–T) boundary.^[69] The concentration of iridium in seawater and marine sediment is sensitive to marine oxygenation, seawater temperature, and various geological and biological processes.^[70]

Iridium in sediments can come from cosmic dust, volcanoes, precipitation from seawater, microbial processes, or hydrothermal vents,^[70] and its abundance can be strongly indicative of the source.^[71][70] It tends to associate with other ferrous metals in manganese nodules.^[68] Iridium is one of the characteristic elements of extraterrestrial rocks, and, along with osmium, can be used as a tracer element for meteoritic material in sediment.^[72][73] For example, core samples from the Pacific Ocean with elevated iridium levels suggested the Eltanin impact of about 2.5 million years ago.^[14]

Some of the mass extinctions, such as the Cretaceous extinction, can be identified by anomalously high concentrations of iridium in sediment, and these can be linked to major asteroid impacts.^[74]

The Cretaceous–Paleogene boundary of 66 million years ago, marking the temporal border between the Cretaceous and Paleogene periods of geological time, was identified by a thin stratumofiridium-rich clay.^[75] A team led by Luis Alvarez proposed in 1980 an extraterrestrial origin for this iridium, attributing it to an asteroidorcomet impact.^[75] Their theory, known as the Alvarez hypothesis, is now widely accepted to explain the extinction of the non-avian dinosaurs. A large buried impact crater structure with an estimated age of about 66 million years was later identified under what is now the Yucatán Peninsula (the Chicxulub crater).^[76][77] Dewey M. McLean and others argue that the iridium may have been of volcanic origin instead, because Earth's core is rich in iridium, and active volcanoes such as Piton de la Fournaise, in the island of Réunion, are still releasing iridium.^[78][79]

2.6

$415.25/ozt ($13.351/g)

2.5

$294.62/ozt ($9.472/g)

3.3

$93.02/ozt ($2.991/g)

3.60

$185.33/ozt ($5.958/g)

3.86

$169.51/ozt ($5.450/g)

4.08

$349.45/ozt ($11.235/g)

3.70

$444.43/ozt ($14.289/g)

3.10

$448.34/ozt ($14.414/g)

2.52

$420.4/ozt ($13.52/g)

10.40

$642.15/ozt ($20.646/g)

9.36

$1,035.87/ozt ($33.304/g)

5.54

$1,066.23/ozt ($34.280/g)

6.16

$826.45/ozt ($26.571/g)

6.1

$556.19/ozt ($17.882/g)

7.81

$544/ozt ($17.5/g)

7.71

$586.90/ozt ($18.869/g)

n.d.

$908.35/ozt ($29.204/g)

n.d.

$1,293.27/ozt ($41.580/g)

n.d.

$1,485.80/ozt ($47.770/g)

n.d.

$1,633.51/ozt ($52.519/g)

n.d.

$5,400.00/ozt ($173.614/g)

n.d.

$3,980.00/ozt ($127.960/g)

n.d.

$4,652.38/ozt ($149.577/g)

n.d.

$5,000.00/ozt ($160.754/g)

Worldwide production of iridium was about 7,300 kilograms (16,100 lb) in 2018.^[81] The price is high and varying (see table). Illustrative factors that affect the price include oversupply of Ir crucibles^[80][82] and changes in LED technology.^[83]

Platinum metals occur together as dilute ores. Iridium is one of the rarer platinum metals: for every 190 tonnes of platinum obtained from ores, only 7.5 tonnes of iridium is isolated.^[84] To separate the metals, they must first be brought into solution. Two methods for rendering Ir-containing ores soluble are (i) fusion of the solid with sodium peroxide followed by extraction of the resulting glass in aqua regia and (ii) extraction of the solid with a mixture of chlorine with hydrochloric acid.^[40][67] From soluble extracts, iridium is separated by precipitating solid ammonium hexachloroiridate ((NH
₄)
₂IrCl
₆) or by extracting IrCl²⁻
₆ with organic amines.^[85] The first method is similar to the procedure Tennant and Wollaston used for their original separation. The second method can be planned as continuous liquid–liquid extraction and is therefore more suitable for industrial scale production. In either case, the product, an iridium chloride salt, is reduced with hydrogen, yielding the metal as a powder or sponge, which is amenable to powder metallurgy techniques.^[86][87] Iridium is also obtained commercially as a by-product from nickel and copper mining and processing. During electrorefining of copper and nickel, noble metals such as silver, gold and the platinum group metals as well as selenium and tellurium settle to the bottom of the cell as anode mud, which forms the starting point for their extraction.^[80]

2017

2018

2019

2020

7,720

7,180

7,540

7,910

8,170

6,624

6,057

6,357

6,464

6,786

598

619

586

845

836

300

200

400

300

300

200

300

200

300

250

Due to iridium's resistance to corrosion it has industrial applications. The main areas of use are electrodes for producing chlorine and other corrosive products, OLEDs, crucibles, catalysts (e.g. acetic acid), and ignition tips for spark plugs.^[84]

Resistance to heat and corrosion are the bases for several uses of iridium and its alloys.

Owing to its high melting point, hardness, and corrosion resistance, iridium is used to make crucibles. Such crucibles are used in the Czochralski process to produce oxide single-crystals (such as sapphires) for use in computer memory devices and in solid state lasers.^[89][90] The crystals, such as gadolinium gallium garnet and yttrium gallium garnet, are grown by melting pre-sintered charges of mixed oxides under oxidizing conditions at temperatures up to 2,100 °C (3,810 °F).^[16]

Certain long-life aircraft engine parts are made of an iridium alloy, and an iridium–titanium alloy is used for deep-water pipes because of its corrosion resistance.^[25] Iridium is used for multi-pored spinnerets, through which a plastic polymer melt is extruded to form fibers, such as rayon.^[91] Osmium–iridium is used for compass bearings and for balances.^[16]

Because of their resistance to arc erosion, iridium alloys are used by some manufacturers for the centre electrodes of spark plugs,^[89][92] and iridium-based spark plugs are particularly used in aviation.

Iridium compounds are used as catalysts in the Cativa process for carbonylationofmethanol to produce acetic acid.^[93][94]

Iridium complexes are often active for asymmetric hydrogenation both by traditional hydrogenation.^[95] and transfer hydrogenation.^[96] This property is the basis of the industrial route to the chiral herbicide (S)-metolachlor. As practiced by Syngenta on the scale of 10,000 tons/year, the complex [Ir(COD)Cl]₂ in the presence of Josiphos ligands.^[97]

The radioisotope iridium-192 is one of the two most important sources of energy for use in industrial γ-radiography for non-destructive testing of metals.^[98][99] Additionally, ¹⁹²
Ir
is used as a source of gamma radiation for the treatment of cancer using brachytherapy, a form of radiotherapy where a sealed radioactive source is placed inside or next to the area requiring treatment. Specific treatments include high-dose-rate prostate brachytherapy, biliary duct brachytherapy, and intracavitary cervix brachytherapy.^[25] Iridium-192 is normally produced by neutron activation of isotope iridium-191 in natural-abundance iridium metal.^[100]

Iridium complexes are key components of white OLEDs. Similar complexes are used in photocatalysis.^[101]

An alloy of 90% platinum and 10% iridium was used in 1889 to construct the International Prototype Meter and kilogram mass, kept by the International Bureau of Weights and Measures near Paris.^[25] The meter bar was replaced as the definition of the fundamental unit of length in 1960 by a line in the atomic spectrumofkrypton,^[d][102] but the kilogram prototype remained the international standard of mass until 20 May 2019, when the kilogram was redefined in terms of the Planck constant.^[103]

Iridium–osmium alloys were used in fountain pen nib tips. The first major use of iridium was in 1834 in nibs mounted on gold.^[16] Starting in 1944, the famous Parker 51 fountain pen was fitted with a nib tipped by a ruthenium and iridium alloy (with 3.8% iridium). The tip material in modern fountain pens is still conventionally called "iridium", although there is seldom any iridium in it; other metals such as ruthenium, osmium, and tungsten have taken its place.^[104]

An iridium–platinum alloy was used for the touch holes or vent pieces of cannon. According to a report of the Paris Exhibition of 1867, one of the pieces being exhibited by Johnson and Matthey "has been used in a Whitworth gun for more than 3000 rounds, and scarcely shows signs of wear yet. Those who know the constant trouble and expense which are occasioned by the wearing of the vent-pieces of cannon when in active service, will appreciate this important adaptation".^[105]

The pigment iridium black, which consists of very finely divided iridium, is used for painting porcelain an intense black; it was said that "all other porcelain black colors appear grey by the side of it".^[106]

Iridium in bulk metallic form is not biologically important or hazardous to health due to its lack of reactivity with tissues; there are only about 20 parts per trillion of iridium in human tissue.^[25] Like most metals, finely divided iridium powder can be hazardous to handle, as it is an irritant and may ignite in air.^[67] By 2015 very little is known about the toxicity of iridium compounds,^[107] primarily because it is used so rarely that few people come in contact with it and those who do only with very small amounts. However, soluble salts, such as the iridium halides, could be hazardous due to elements other than iridium or due to iridium itself.^[31] At the same time, most iridium compounds are insoluble, which makes absorption into the body difficult.^[25]

A radioisotope of iridium, ¹⁹²
Ir, is dangerous, like other radioactive isotopes. The only reported injuries related to iridium concern accidental exposure to radiation from ¹⁹²
Ir used in brachytherapy.^[31] High-energy gamma radiation from ¹⁹²
Ir can increase the risk of cancer. External exposure can cause burns, radiation poisoning, and death. Ingestion of ¹⁹²Ir can burn the linings of the stomach and the intestines.^{[108] 192}Ir, ^192mIr, and ^194mIr tend to deposit in the liver, and can pose health hazards from both gamma and beta radiation.^[62]

• IridiumatThe Periodic Table of Videos (University of Nottingham)
• Iridium in Encyclopædia Britannica