 |
This article needs additional citations for verification. Please help improve this articlebyadding citations to reliable sources. Unsourced material may be challenged and removed.
Find sources: "DSLAM" – news · newspapers · books · scholar · JSTOR (December 2013) (Learn how and when to remove this message) |
Adigital subscriber line access multiplexer (DSLAM, often pronounced DEE-slam) is a network device, often located in telephone exchanges, that connects multiple customer digital subscriber line (DSL) interfaces to a high-speed digital communications channel using multiplexing techniques.[1] Its cable internet (DOCSIS) counterpart is the cable modem termination system.
The DSLAM equipment collects the data from its many modem ports and aggregates their voice and data traffic into one complex composite "signal" via multiplexing. Depending on its device architecture and setup, a DSLAM aggregates the DSL lines over its Asynchronous Transfer Mode (ATM), Frame Relay, and/or Internet Protocol network, i.e., an IP-DSLAM using Packet Transfer Mode - Transmission Convergence (PTM-TC) protocol(s) stack.
The aggregated traffic is then directed to a telco's backbone switch, via an access network (AN), also called a Network Service Provider (NSP), at up to 10 Gbit/s data rates.
The DSLAM acts like a network switch since its functionality is at the link layer. Therefore, it cannot re-route traffic between multiple IP networks, only between ISP devices and end-user connection points. The DSLAM traffic is switched to a Broadband Remote Access Server where the end-user traffic is then routed across the ISP network to the Internet. Customer-premises equipment that interfaces well with the DSLAM to which it is connected may take advantage of enhanced telephone voice and data line signaling features and the bandwidth monitoring and compensation capabilities it supports.
A DSLAM may or may not be located in the telephone exchange, and may also serve multiple data and voice customers within a neighborhood serving area interface, sometimes in conjunction with a digital loop carrier. DSLAMs are also used by hotels, lodges, residential neighborhoods, and other businesses operating their own private telephone exchange.
In addition to being a data switch and multiplexer, a DSLAM is also a large collection of modems. Each modem on the aggregation card communicates with a single subscriber's DSL modem. This modem functionality is integrated into the DSLAM itself instead of being done via individual external devices like 20th-century voiceband modems used for dial-up internet.
Like traditional voice-band modems, a DSLAM's integrated DSL modems are usually able to probe the line and to adjust themselves to electronically or digitally compensate for forward echoes and other bandwidth-limiting factors in order to move data at the maximum possible connection rate.
This compensation capability also takes advantage of the better performance of "balanced line" DSL connections, providing capabilities for LAN segments longer than physically similar unshielded twisted pair (UTP) Ethernet connections, since the balanced line type is generally required for its hardware to function correctly. This is due to the nominal line impedance (measured in Ohms but comprising both resistance and inductance) of balanced lines being somewhat lower than that of UTP, thus supporting 'weaker' signals (however the solid-state electronics required to construct such digital interfaces are more costly). Many early DSLAMs required a separate splitter rack to split POTS service from ADSL service,[2][3][4][5][6] but newer DSLAMs can be connected directly to phone lines as they have built-in splitters.[7][8][9][10]
Balanced pair cable has higher attenuation at higher frequencies. Therefore, the longer the wire between DSLAM and subscriber, the slower the maximum possible data rate due to the lower frequencies being used to limit the total attenuation (or due to the higher number of errors at higher frequencies, effectively lowering the overall frequency/data rate). The following is a rough guide to the relation between wire distance (based on 0.40 mm copper and ADSL2+ technology) and maximum data rate. Local conditions may vary, especially beyond 2 km, often necessitating a closer DSLAM to bring acceptable bandwidths:
Customers connect to the DSLAM through ADSL modems or DSL routers, which are connected to the PSTN network via typical unshielded twisted pair telephone lines. Each DSLAM has multiple aggregation cards, and each such card can have multiple ports to which the customers' lines are connected. Typically a single DSLAM aggregation card has 24 ports, but this number can vary with each manufacturer.
The most common DSLAMs are housed in a telco-grade chassis, which are supplied with (nominal) 48 volts DC. Hence a typical DSLAM setup may contain power converters, DSLAM chassis, aggregation cards, cabling, and upstream links.
On the upstream trunk (ISP) side many early DSLAMs used ATM—and this approach was standardized by the DSL Forum—with Gigabit Ethernet support appearing sometime later.[11] Today, the most common upstream links in these DSLAMs use Gigabit Ethernet or multi-gigabit fiber optic links.[citation needed]
IP-DSLAM stands for Internet Protocol Digital Subscriber Line Access Multiplexer. User traffic is mostly IP based.
Traditional 20th century DSLAMs used Asynchronous Transfer Mode (ATM) technology to connect to upstream ATM routers/switches. The DSLAM simply extracted the ATM signals from the DSL signal, and passed the ATM signal to ATM routers, which then extract the IP traffic and pass it on to an IP router in an IP network. This division of work was thought to be sensible because DSL itself is based on ATM, and could theoretically carry data other than IP in that ATM stream. In contrast, an IP-DSLAM extracts the IP traffic in the DSLAM itself and passes it on to an IP router. The advantages of IP-DSLAM over a traditional ATM DSLAM are that the merged equipment is less expensive to make and operate and can offer a richer set of features.
|
Digital subscriber line (DSL) technologies
| |||||
|---|---|---|---|---|---|
| Symmetric |
| ||||
| Asymmetric |
| ||||
| Related |
| ||||
