Contents

Friis transmission equation

Part of a serieson
Antennas
Common types Dipole Fractal Loop Monopole Satellite dish Television Whip
Components Balun Block upconverter Coaxial cable Counterpoise (ground system) Feed Feed line Low-noise block downconverter Passive radiator Receiver Rotator Stub Transmitter Tuner Twin-lead
Systems Antenna farm Amateur radio Cellular network Hotspot Municipal wireless network Radio Radio masts and towers Wi-Fi Wireless
Safety and regulation Wireless device radiation and health Wireless electronic devices and health International Telecommunication Union (Radio Regulations) World Radiocommunication Conference
Radiation sources / regions Boresight Focal cloud Ground plane Main lobe Near and far field Side lobe Vertical plane
Characteristics Array gain Directivity Efficiency Electrical length Equivalent radius Factor Friis transmission equation Gain Height Radiation pattern Radiation resistance Radio propagation Radio spectrum Signal-to-noise ratio Spurious emission
Techniques Beam steering Beam tilt Beamforming Small cell Bell Laboratories Layered Space-Time (BLAST) Massive Multiple-input multiple-output (MIMO) Reconfiguration Spread spectrum Wideband Space Division Multiple Access (WSDMA)
v t e

The Friis transmission formula is used in telecommunications engineering, equating the power at the terminals of a receive antenna as the product of power density of the incident wave and the effective aperture of the receiving antenna under idealized conditions given another antenna some distance away transmitting a known amount of power.^[1] The formula was presented first by Danish-American radio engineer Harald T. Friis in 1946.^[2] The formula is sometimes referenced as the Friis transmission equation.

Friis' original formula[edit]

Friis' original idea behind his transmission formula was to dispense with the usage of directivityorgain when describing antenna performance. In their place is the descriptor of antenna capture area as one of two important parts of the transmission formula that characterizes the behavior of a free-space radio circuit.^[2]

This leads to his published form of his transmission formula:

${\displaystyle {\frac {P_{r}}{P_{t}}}=\left({\frac {A_{r}A_{t}}{d^{2}\lambda ^{2}}}\right)}$

where:

• ${\displaystyle P_{t}}$ is the power fed into the transmitting antenna input terminals;^[2]
• ${\displaystyle P_{r}}$ is the power available at receiving antenna output terminals;^[2]
• ${\displaystyle A_{r}}$ is the effective aperture area of the receiving antenna;^[2]
• ${\displaystyle A_{t}}$ is the effective aperture area of the transmitting antenna;^[2]
• ${\displaystyle d}$ is the distance between antennas;^[2]
• ${\displaystyle \lambda }$ is the wavelength of the radio frequency;^[2]
• ${\displaystyle P_{t}}$ and ${\displaystyle P_{r}}$ are in the same units of power;^[2]
• ${\displaystyle A_{r}}$, ${\displaystyle A_{t}}$, ${\displaystyle d^{2}}$, and ${\displaystyle \lambda ^{2}}$ are in the same units.^[2]
• Distance ${\displaystyle d}$ large enough to ensure a plane wave front at the receive antenna sufficiently approximated by ${\displaystyle d\geq 2a^{2}/\lambda }$ where ${\displaystyle a}$ is the largest linear dimension of either of the antennas.^[2]

Friis stated the advantage of this formula over other formulations is the lack of numerical coefficients to remember, but does require the expression of transmitting antenna performance in terms of power flow per unit area instead of field strength and the expression of receiving antenna performance by its effective area rather than by its power gain or radiation resistance.^[2]

Contemporary formula[edit]

Few follow Friis' advice on using antenna effective area to characterize antenna performance over the contemporary use of directivity and gain metrics. Replacing the effective antenna areas with their gain counterparts yields

${\displaystyle {\frac {P_{r}}{P_{t}}}=G_{t}G_{r}\left({\frac {\lambda }{4\pi d}}\right)^{2}}$

where ${\displaystyle G_{t}}$ and ${\displaystyle G_{r}}$ are the antenna gains (with respect to an isotropic radiator) of the transmitting and receiving antennas respectively, ${\displaystyle \lambda }$ is the wavelength representing the effective aperture area of the receiving antenna, and ${\displaystyle d}$ is the distance separating the antennas.^[1] To use the equation as written, the antenna gains are unitless values, and the units for wavelength (${\displaystyle \lambda }$) and distance (${\displaystyle d}$) must be the same.

To calculate using decibels, the equation becomes:

${\displaystyle P_{r}^{\mathsf {[$dB]}}=P_{t}^{\mathsf {[dB]}}+G_{t}^{\mathsf {[dBi]}}+G_{r}^{\mathsf {[dBi]}}+20\log _{10}\left({\frac {\lambda }{4\pi d}}\right)}

where:

• ${\displaystyle P_{t}^{[$dB]}} is the power delivered to the terminals of an isotropic transmit antenna, expressed in dB.^[3]
• ${\displaystyle P_{r}^{\mathsf {[$dB]}}} is the available power at the receive antenna terminals equal to the product of the power density of the incident wave and the effective aperture area of the receiving antenna proportional to ${\displaystyle \lambda ^{2}}$, in dB.^[1]
• ${\displaystyle G_{t}^{\mathsf {[dBi]}}}$ is the gain of the transmitting antenna in the direction of the receiving antenna, in dB.^[1]
• ${\displaystyle G_{r}^{\mathsf {[dBi]}}}$ is the gain of the receiving antenna in the direction of the transmitting antenna, in dB.^[1]

The simple form applies under the following conditions:

• ${\displaystyle d\gg \lambda }$, so that each antenna is in the far field of the other.^[1]
• The antennas are correctly aligned and have the same polarization.^[4]
• The antennas are in unobstructed free space, with no multipath propagation.^[4]
• The bandwidth is narrow enough that a single value for the wavelength can be used to represent the whole transmission.^[4]
• Directivities are both for isotropic radiators (dBi).
• Powers are both presented in the same units: either both dBm or both dBW.

The ideal conditions are almost never achieved in ordinary terrestrial communications, due to obstructions, reflections from buildings, and most importantly reflections from the ground. One situation where the equation is reasonably accurate is in satellite communications when there is negligible atmospheric absorption; another situation is in anechoic chambers specifically designed to minimize reflections.^[5]

Derivation[edit]

There are several methods to derive the Friis transmission equation. In addition to the usual derivation from antenna theory, the basic equation also can be derived from principles of radiometry and scalar diffraction in a manner that emphasizes physical understanding.^[6] Another derivation is to take the far-field limit of the near-field transmission integral.^[7]

See also[edit]

• Link budget
• Radio propagation model

References[edit]

Further reading[edit]

• Harald T. Friis, "A Note on a Simple Transmission Formula," Proceedings of the I.R.E. and Waves and Electrons, May, 1946, pp 254–256.
• John D. Kraus, "Antennas," 2nd Ed., McGraw-Hill, 1988.
• Kraus and Fleisch, "Electromagnetics," 5th Ed., McGraw-Hill, 1999.
• D.M. Pozar, "Microwave Engineering." 2nd Ed., Wiley, 1998.
• Shaw, J.A. (2013). "Radiometry and the Friis transmission equation". Am. J. Phys. 81 (33): 33–37. Bibcode:2013AmJPh..81...33S. doi:10.1119/1.4755780.

External links[edit]

• Derivation of Friis Transmission Formula
• Friis Transmission Equation Calculator
• Another Friis Transmission Equation Calculator
• Seminar Notes by Laasonen