 |
This article may be too technical for most readers to understand. Please help improve ittomake it understandable to non-experts, without removing the technical details. (May 2022) (Learn how and when to remove this message)
|
Immersion cooling is an IT cooling practice by which complete servers are immersed in a dielectric, electrically non-conductive fluid that has significantly higher thermal conductivity than air. Heat is removed from a system by putting the coolant in direct contact with hot components, and circulating the heated liquid through heat exchangers. This practice is highly effective because liquid coolants can absorb more heat from the system, and are more easily circulated through the system, than air. Immersion cooling has many benefits, including but not limited to: sustainability, performance, reliability and cost.
Unlike many other devices, computers cannot use immersion water cooling, because ordinary water is electrically conductive and will break electronic components. Therefore, the fluids used in immersion cooling are dielectric liquids to ensure that they can safely come into contact with energized electronic components.
In general, the dielectric liquids used for immersion cooling fall into two categories: hydrocarbons (i.e. mineral, synthetic, or biological oils) and fluorocarbons (fully engineered liquids). Dielectric liquids are divided into single- and two-phase applications, which differ in whether or not the cooling fluid turns into a gas during the cooling cycle.
Anenclosed chassis require dripless connectors to interface to the individual chassis. These chassis are usually based on traditional rack style implementations. The dripless connectors usually require a small closed-circuit cooling loop with a coolant to protect the flow integrity through relatively small pipes and connectors. The closed circuit is facilitated by a CDU or Coolant Distribution Unit, which usually can facilitate multiple racks at once.
Anopen bath refers to the "open" liquid–air interface and thus surface tension between the liquid and the air is a distinctive element. Open bath systems are usually tanks which contain a larger body of dielectric liquid where electronics are immersed into the bath. Multiple electronic assemblies share the same liquid. This liquid can be based on single- or two-phase technology. Regardless of the term, open-bath systems can be fully sealed, but are always opened from the top to service IT equipment. The coolant tank for open bath immersion systems is either connected to a CDU which circulates the dielectric liquid, or to an integrated heat exchanging device which is part of the tank. For a facility interface, CDUs are usually designed for 100 kW or more, whereas an integrated heat exchanging device is usually designed for 10-100 kW cooling capacity.
Hybrid cooling refers to combinations of enclosed and open bath apparatus.[3]
Immersion cooling reduces energy consumption through the elimination of the air cooling infrastructure including on-board server fans, CRACs, A/C compressors, air-circulation fans, necessary duct work, air handlers, and other active ancillary systems such as dehumidifiers. These systems are replaced with liquid circulation pumps and heat exchanger and/or dry cooler systems.
Power use at data centers is often measured in terms of power usage effectiveness (PUE). The definitions of PUE for air-cooled devices and liquid immersion cooled devices are different which makes such direct comparisons inaccurate. The PUE for air-cooled data centers includes the power used by the fans and other active cooling components found in the servers. The PUE for liquid immersion cooling excludes these values from the IT Equipment Energy component because these system elements (in particular on-board fans) are generally removed from the IT equipment as they are not necessary to circulate the dielectric coolants. This discrepancy in the definition of PUE for the different cooling methods results in the PUE of air-cooled data centers generally being overstated when compared against the PUE of a liquid immersion cooled facility of the same power usage.[4]
Servers and other IT hardware cooled by immersion cooling do not require fans to circulate the dielectric liquid, thus they are removed from the system prior to immersion. Thermal pastes which are typically used on heat spreaders for CPUs and other chips may require replacement with a different compound in order to avoid the thermal degradation within the dielectric liquid.[5] Depending on the type of application, solder, Indium foil, and thermally conductive epoxies may be used as a replacement materials.
The temperatures used in immersion cooling are determined by the highest temperature at which the devices being immersed can reliably operate. For servers this temperature range is typically between 15 and 65 °C (59 and 149 °F);[6] however, in ASIC-based crypto mining devices, this range is often extended up to 75 °C.[7] This increase in the high end of the temperature range allows data center operators to use entirely passive dry coolers, or much more efficient evaporative or adiabatic cooling towers[8] instead of chiller-based air cooling or water chillers. This increase in the temperature range also allows operators using single-phase immersion coolants to more effectively use the change in outdoor temperatures to get more efficient cooling from their systems because the single-phase systems are not limited in their effectiveness by the boiling point of the coolant as is the case with two-phase coolants.[9]
Multiple relevant brands like Intel and Facebook have already validated the advantages of submerging servers.[10][11]
Current commercial applications for immersion cooling range from datacenter-oriented solutions for commodity server cooling,[12][13] server clusters, HPCC applications[14] and cryptocurrency mining.[15] and mainstream cloud-based and web hosting architectures. Electric vehicle and battery manufacturers also employ liquid immersion cooling in batteries, drive-train, kinetic energy recovery systems, electric motors, electric motor controllers, and other on-board electronic subsystems.[citation needed] Liquid immersion cooling is also used in the thermal management of LEDs, lasers, X-Ray machines, and magnetic resonance imaging devices.[citation needed]
Immersion cooling is applied to electronic components in deep-sea research where remotely operated underwater vehicles with electronic equipment are filled with single-phase liquid dielectrics to both protect them from corrosion in seawater and as a pressure-compensating fluid to prevent the housing from being crushed by the extreme pressure exerted on the ROV while working in the deep sea.[citation needed] This application also includes the cooling of the electric motors used for under sea propulsion.
Until about 2014, the technology was typically only utilized in special very intensive supercomputing projects, like the Cray Computer Applications.[16] Even though the expected increase in global energy consumption by data centers has remained steady,[17] there is an increased focus on energy efficiency which has driven the utilizing of liquid immersion cooling in both data centers and crypto mining operations to reevaluate its application. The advent of new very high density CPUs and GPUs for use in real-time processing, artificial intelligence, machine learning, and data mining operations is leading users and data center operators to evaluate liquid immersion cooling for ability to cool high density racks as well as reduce the total mechanical footprint of data centers.
 |
This section needs additional citations for verification. Please help improve this articlebyadding citations to reliable sources in this section. Unsourced material may be challenged and removed. (February 2022) (Learn how and when to remove this message)
|
19th and 20th century immersion milestones:
21st century immersion milestones:
Open-bath immersion cooling is a data center cooling technique that implies fully submerging IT equipment in dielectric liquid. The "open" aspect does not refer to an open or sealed system, but refers to the "open" liquid-air interface and thus surface tension between the liquid and the air is a distinctive element.[26]
These baths allow the coolant fluid to be moved through the hardware components or servers submerged in it.[27]
Dual-loop single-phase immersion requires circulation of the dielectric liquids by pumps or by natural convection flow.[28] These liquids always remain in liquid state while operating. They never boil or freeze. The dielectric coolant is either pumped through an external heat exchanger where it is cooled with any facility coolant, or the facility coolant is pumped through an immersed heat exchanger, which facilitates heat transfer within the dielectric liquid.
Intwo-phase systems, fluorocarbons[29] are used as heat transfer fluids. Heat is removed in a two-phase system, where the liquid boils when it comes in contact with hot components due to its low boiling point.[30] The system takes advantage of a concept known as "latent heat" which is the heat (thermal energy) required to change the phase of a fluid, this occurs when the two-phase coolant comes in contact with the heated electronics in the bath that are above the coolants boiling point. After the two-phase coolant enters its gas phase it must be cooled or condensed, typically through the use of water-cooled coils placed in the top of the tank. After it is condensed, the two-phase coolant drips back into the primary cooling tank. The two-phase coolant in the tank generally remains at its "saturation temperature". Energy transferred from the servers into the two-phase coolant will cause a portion of it to boil off into a gas. The gas rises above the liquid level where it contacts a condenser which is cooler than the saturation temperature. This causes the gaseous coolant to condense back into a liquid and fall back into the bath.[31]
Sealed server immersion cooling encloses servers in liquid-tight casings. The dielectric coolant is circulated inside or pumped through each server to collect heat from the components. The heated fluid is circulated to a heat exchanger in the rack where it is either circulated directly outside the building to a cooling tower or to a heat exchanger or cooled directly at the rack with a facility coolant infrastructure.[32] The main advantage of this approach is that servers are mounted in self-contained vessels that can be replaced in the rack without accessing the fluid. A disadvantage is that not all hardware can be used as the vendor defines the hardware specs of the sealed servers.
Some hydrocarbon-based immersion cooling fluids provide a fire hazard as they have a fire point.[33]
In the last few years[when?], immersion cooling in particular for bitcoin mining has become a popular method to generate usable heat. In cold climates a single ASIC miner can provide ultra-high-efficiency electric heat conversion sufficient to heat an entire home. Immersion cooling offered a means to silently convert the waste heat from the mining operation to heat water, melt snow, power in-floor heating, and heat hot tubs, pools, shops, outbuildings, sheds, and greenhouses. There is a compelling case to combine bitcoin mining operations with indoor vertical farms and traditional greenhouses to offset or eliminate the heating cost of the facilities. Indoor and outdoor recreation facilities both public and private can also benefit from the "free" waste heat. Some companies provide computing-based heating for residential and commercial operations.[citation needed]
Overheating of Li-ion cells and battery packs is an ongoing technological challenge for electrochemical energy conversion and storage, including in electric vehicles. Immersion cooling is a promising thermal management technique to address these challenges.[34] Immersion cooling of batteries is specifically beneficial in abuse conditions, where the thermal propagation is needed to be avoided across the battery module or pack. Immersion cooling is gaining prominence as an emerging application within the automotive industry. With a heat transfer capability 50 to 100 times greater than indirect cooling methods, immersion cooling stands out as an efficient and powerful solution.[35] Presently, immersion cooling is predominantly utilized in motorsport and high-end vehicle models, showcasing its effectiveness in cutting-edge automotive technologies.[36]
