This is a template for generating a junction list or an exit for a route article. Please note, if a section of the table has numbered exits, you must follow the coding for exit lists throughout the table; omitting the |exitor|old after the template name will result in formatting errors on at-grade junctions. If a highway has a freeway section, and none of those exits are numbered, you may use the coding for at-grade junction lists.
If a freeway has named interchanges, like the Pennsylvania Turnpike, add |name after either |exitor|old.
Junction list usage
This is the basic syntax you need to get a complete junction table for roads that only have at-grade intersections. Just copy and paste the code below:
This is the basic syntax you need to get a complete exit list table for roads that have numbered grade-separated interchanges. Just copy and paste the code below:
Exit list usage for roadways with old exit numbers
This is the basic syntax you need to get a complete exit list table for roads that have numbered grade-separated interchanges and old exit numbers. Just copy and paste the code below:
For the above parameters, here's what you should fill in:
state: the state the intersection is at, do not use if cspan or lspan is specified for the row (use the state's postal abbreviation)
sspan: set to add a column for the state/province in a multi-state/provincial junction list. This uses the state or province's abbreviation to generate the link. This parameter needs to be set to the number of rows the state/province spans—if value=1, do not omit this parameter
state_special: (replaces state) state/province where the junction is located—use for custom entries only. Full wiki markup is required.
county: name of the county without wiki markup—the county is automatically linked by the template
cspan: number of rows the county spans—if value=1, omit this parameter
county_special: (replaces county) county (or equivalent) where the junction is located—use for custom entries only. Full wiki markup is required.
county_note: used to display a note, such as county mileage, in small text below the county name—used primarily for California.
location: name of the location without wiki markup—the location is automatically linked by the template. When an intersection is not in any location as is often the case in states outside of the northeast, either |location=none (preferred) or |location= (deprecated) will create a blank cell.
lspan: number of rows the location spans. If value=1, omit this parameter. Ignored when |location=noneor|location= .
location_special: (replaces location) location where the junction is located—use for custom entries only. Full wiki markup is required. Ignored when |location= is set.
area: (optional for use with location) used to disambiguate between town, city, village, etc.
ctdab: (optional for use with location) further disambiguation by county (BrightoninNew York is an example where this tag would be used)
indep_city: set to "yes" if the location in "location" is an independent city
indep_city_special: (replaces location and indep_city) independent city where junction is located—use for custom entries only. Full wiki markup is required.
type: use to specify a shading for that junction's row. The permitted types are:
closed: for highway junctions that are now closed to traffic
unbuilt: for unbuilt roadway junctions/interchanges
incomplete: for incomplete intersections/interchanges where all movements are not supported (Northbound exit and southbound entrance, no westbound exit, etc.)
HOV: for high-occupancy vehicle-only intersections/interchanges
etcortoll: for intersections/interchanges that involve a toll; on toll roads this could be for intersections/interchanges where only electronic toll collection is offered
trans: use to specify point at which a highway transitions from one designation to another
mile: milepost of the junction. If unknown, leave blank.
km: if the table uses kilometres instead of miles.
mile2orkm2: the second measurement if the location is in a range of miles or kilometres instead of one stated point.
mspan to span multiple rows with the same mileage. Use |mile=none in the spanned rows.
exit: exit number of the junction. If the junction is not a numbered exit, leave blank; if an exit is unnumbered, either leave blank or insert an em dash (—) as desired.
old: If the roadway had its exit numbers changed, use this to indicate the old number.
name: If a freeway has named interchanges, like the Pennsylvania Turnpike, use this to set the name for the interchange.
road: road that the article route intersects at this junction. To generate the proper coding, use the {{jct}} template.
notes: any notes regarding that junction. This must include an explanation for any usage of the type-generated shading.
nspan: number of rows the notes span. If value=1, omit this parameter.