Contents

Degree of curvature

This article includes a list of references, related reading, or external links, but its sources remain unclear because it lacks inline citations. Please help improve this article by introducing more precise citations. (September 2023) (Learn how and when to remove this message)

Degree of curveordegree of curvature is a measure of curvature of a circular arc used in civil engineering for its easy use in layout surveying.

The degreeofcurvature is defined as the central angle to the ends of an agreed length of either an arc or a chord;^[1] various lengths are commonly used in different areas of practice. This angle is also the change in forward direction as that portion of the curve is traveled. In an n-degree curve, the forward bearing changes by n degrees over the standard length of arc or chord.

Curvature is usually measured in radius of curvature. A small circle can be easily laid out by just using radius of curvature, but degree of curvature is more convenient for calculating and laying out the curve if the radius is large as a kilometer or a mile, as it needed for large scale works like roads and railroads. By using degrees of curvature, curve setting can be easily done with the help of a transitortheodolite and a chain, tape, or rope of a prescribed length.

The usual distance used to compute degree of curvature in North American road work is 100 feet (30.5 m) of arc.^{[2][page needed]} Conversely, North American railroad work traditionally used 100 feet of chord, which is used in other places^[where?] for road work. Other lengths may be used—such as 100 metres (330 ft) where SI is favoured or a shorter length for sharper curves. Where degree of curvature is based on 100 units of arc length, the conversion between degree of curvature and radius is Dr = 18000/π ≈ 5729.57795, where D is degree and r is radius.

Since rail routes have very large radii, they are laid out in chords, as the difference to the arc is inconsequential; this made work easier before electronic calculators became available.

The 100 feet (30.48 m) is called a station, used to define length along a road or other alignment, annotated as stations plus feet 1+00, 2+00, etc. Metric work may use similar notation, such as kilometers plus meters 1+000.

Degree of curvature can be converted to radius of curvature by the following formulae:

${\displaystyle r={\frac {180^{\circ }A}{\pi D_{\text{C}}}}}$

where ${\displaystyle A}$isarc length, ${\displaystyle r}$ is radius of curvature, and ${\displaystyle D_{\text{C}}}$ is degree of curvature, arc definition

Substitute deflection angle for degree of curvature or make arc length equal to 100 feet.

${\displaystyle r={\frac {C}{2\sin \left({\frac {D_{\text{C}}}{2}}\right)}}}$

where ${\displaystyle C}$ is chord length, ${\displaystyle r}$ is radius of curvature and ${\displaystyle D_{\text{C}}}$ is degree of curvature, chord definition

${\displaystyle D_{\text{C}}=5729.58/r}$

As an example, a curve with an arc length of 600 units that has an overall sweep of 6 degrees is a 1-degree curve: For every 100 feet of arc, the bearing changes by 1 degree. The radius of such a curve is 5729.57795. If the chord definition is used, each 100-unit chord length will sweep 1 degree with a radius of 5729.651 units, and the chord of the whole curve will be slightly shorter than 600 units.

This article includes a list of general references, but it lacks sufficient corresponding inline citations. Please help to improve this article by introducing more precise citations. (June 2021) (Learn how and when to remove this message)

• "Degree of Curvature". 2005-02-12. Archived from the original on 2005-02-12. Retrieved 2021-06-24.
• http://www.tpub.com/content/engineering/14071/css/14071_242.htm Archived 2005-01-27 at the Wayback Machine
• "Just how sharp is that curve?". 2005-02-23. Archived from the original on 2005-02-23. Retrieved 2021-06-24.
• "Interactive Highway Design".
• "Degrees of Curve". www.trainweb.org. Retrieved 2021-06-24.
• "CIRCULAR CURVE". 2004-12-13. Archived from the original on 2004-12-13. Retrieved 2021-06-24.
• "Horizontal circular curves are used to transition the change in alignment at angle points in the tangent (straight) portions of alignments". 2005-03-04. Archived from the original on 2005-03-04. Retrieved 2021-06-24.
• [1]
• "Sec. 5. Final subdivision plat". 2004-09-17. Archived from the original on 2004-09-17. Retrieved 2021-06-24.