Contents

Southwest Airlines Flight 2294

Southwest Airlines Flight 2294

N387SW, the aircraft involved in the incident, photographed in 2006
Incident
Date	July 13, 2009 (2009-07-13)
Summary	In-flight structural failure leading to rapid decompression
Site	near Charleston, WV
Aircraft
Aircraft type	Boeing 737-3H4
Operator	Southwest Airlines
Registration	N387SW
Flight origin	Nashville International Airport (KBNA)
Destination	Baltimore Washington International Airport (KBWI)
Occupants	131
Passengers	126
Crew	5
Fatalities	0
Injuries	0
Survivors	131

Southwest Airlines Flight 2294 (WN2294/SWA2294) was a scheduled US passenger aircraft flight which suffered a rapid depressurization of the passenger cabin on July 13, 2009. The aircraft made an emergency landingatYeager Airport in Charleston, West Virginia, with no fatalities or major injuries to passengers and crew. An NTSB investigation found that the incident was caused by a failure in the fuselage skin due to metal fatigue.^[1]

The aircraft involved was a Boeing 737-3H4,^[a] registration N387SW,^[2] serial number 26602. 126 passengers and 5 crew members were on board, on a scheduled flight from Nashville International AirporttoBaltimore/Washington International Airport.^[3] The aircraft took off from Nashville at 4:05 pm CDT (5:05 pm EDT) and climbed for about 25 minutes, leveling off at a cruising altitude of approximately 35,000 feet (11,000 m).^[1]

At about 5:45 pm EDT, the aircraft experienced a rapid decompression event, causing the cabin altitude warning to be activated in the cockpit, indicating a dangerous drop in cabin pressure. Passenger oxygen masks deployed automatically.^[1] The aircraft systems disengaged the autopilot, and the captain began an emergency descent to bring the aircraft down into denser air to prevent passenger hypoxia. The cabin altitude alarm ceased as the aircraft passed through about 9,000 feet (2,700 m).

The flight crew declared an emergency and landed the aircraft safely at Yeager Airport in Kanawha County, West Virginia, near Charleston. After landing, the aircraft was found to have a three-sided hole in the fuselage, 17.4 inches (44 cm) long, and between 8.6 to 11.5 inches (22 to 29 cm) wide, forward of the leading edge of the vertical stabilizer, at the rear end of the aircraft.^[1]

The accident was investigated by the Federal Aviation Administration (FAA) and the National Transportation Safety Board (NTSB). NTSB review of the cockpit voice recorder records, and post-incident interviews, showed that the flight crew acted appropriately in response to the emergency. The NTSB investigation found that the incident was caused by a metal fatigue crack in the fuselage skin.

The aircraft was delivered to Southwest Airlines in June 1994, and at the time of the accident flight, had accumulated approximately 42,500 takeoff/landing cycles, and 50,500 airframe hours.^[1] Highly magnified inspections found that a long metal fatigue crack had developed at the boundary of two different manufacturing processes used by Boeing in creating the fuselage crown skin assembly.^[1] Boeing finite element modeling had suggested that stress forces in this boundary region are higher due to differences in stiffness, indicating that a failure was more likely to occur in this area after a certain number of pressurization-depressurization cycles.

Following this incident, on September 3, 2009, Boeing issued a Service Bulletin calling for repetitive external inspections to detect any cracks in this more-vulnerable area of the fuselage skin. The FAA then followed up by issuing an Airworthiness Directive on January 12, 2010, mandating these inspection requirements.^[1]

Earlier criticism of the carrier's lax maintenance and inspection practices, for which the airline had been fined $7.5 million in 2008, was quickly echoed.^[4]

On April 1, 2011, less than two years later, a similar incident occurred on Southwest Airlines Flight 812, involving another Southwest Airlines Boeing 737-3H4. In response to the second incident, the FAA issued an Airworthiness Directive requiring more frequent inspections by all airlines operating Boeing 737 Classic aircraft.

As of April 2024^[update], Southwest Flight 2294 is a daily service from HonolulutoHilo, operated by a Boeing 737 MAX 8 aircraft.^[5]

United States

Modern history

• Southwest Airlines information regarding Flight 2294, official blog

Wikinews has related news:

• U.S. investigators probe in-flight hole in passenger jet

38°22′33″N 081°35′35″W / 38.37583°N 81.59306°W / 38.37583; -81.59306