Contents

Ward Leonard control

Basic concept[edit]

The key feature of the Ward Leonard control system is the ability to smoothly vary the speed of a DC motor, including reversing it, by controlling the field and hence the output voltage of a DC generator, as well as the field of the motor itself. As the speed of a DC motor is dictated by the supplied voltage, this gives simple speed control. The DC generator could be driven by any means. This 'prime mover' could be an AC motor, or it could be an internal combustion engine (its application to vehicles was patented by H.W. Leonard in 1903^[2]).

A Ward Leonard drive can be viewed as a high-power amplifier in the multi-kilowatt range, built from rotating electrical machinery. Where the 'prime mover' is electrical, a Ward Leonard drive unit consists of a motor and generator with shafts coupled together. The prime mover, which turns at a constant speed, may be AC or DC powered. The generator is a DC generator, with field windings and armature windings. The input to the amplifier is applied to the field windings, and the higher power output comes from the armature windings. (See Excitation (magnetic)#Amplifier principle for how a generator can act as an amplifier.) The amplifier output is usually connected to a second motor, which moves the load, such as an elevator. With this arrangement, small changes in current applied to the input, and thus the generator field, result in large changes in the output, allowing smooth speed control.^[3]

Aflywheel may be used to reduce voltage fluctuations during sudden load changes. The Ward Leonard system with this modification is known as Ward Leonard Ilgner Control.^[4] In that configuration, the synchronous motor, normally used for Ward Leonard control, is replaced by a wound-rotor induction motor. The combination of an induction motor, flywheel, and generator(s) is known as an Ilgner set. It effectively decouples intermittent short-term high loading of the generator from the AC supply.^[5][6]

A more technical description[edit]

The speed of a DC motor is controlled by varying the voltage fed to the generator field windings, V_gf, which varies the output voltage of the generator. The varied output voltage will change the voltage of the motor, since they are connected directly through the armature. Consequently, changing the V_gf will control the speed of the motor. The picture on the right shows the Ward Leonard control system, with the V_gf feeding the generator and V_mf feeding the motor.^[7]

Transfer function[edit]

The first subscripts 'g' and 'm' each represents generator and motor. The superscripts 'f', 'r',and 'a', correspond to field, rotor, and armature.

• ${\displaystyle W_{i}}$ = plant state vector
• ${\displaystyle K}$ = gain
• ${\displaystyle t}$ = time constant
• ${\displaystyle J}$ = polar moment of inertia
• ${\displaystyle D}$ = angular viscous friction
• ${\displaystyle G}$ = rotational inductance constant
• ${\displaystyle s}$ = Laplace operator

Eq. 1: The generator field equation

${\displaystyle V_{g}^{f}=R_{g}^{f}I_{g}^{f}+L_{g}^{f}I_{g}^{f}}$

Eq. 2: The equation of electrical equilibrium in the armature circuit

${\displaystyle -G_{g}^{f}aI_{g}^{f}W_{g}^{r}+(R_{g}^{a}+R_{m}^{a})I^{a}+(L_{g}^{a}+L_{m}^{a})I^{a}+G_{m}^{f}aI_{m}^{f}W_{m}^{r}=0}$

Eq. 3: Motor torque equation

${\displaystyle -T_{L}=J_{m}W_{m}^{r}+D_{m}W_{m}^{r}}$

With total impedance, ${\displaystyle L_{g}^{a}+L_{m}^{a}}$, neglected, the transfer function can be obtained by solving eq 3 ${\displaystyle T_{L}=0}$.

Eq. 4: Transfer function

${\displaystyle {\frac {W_{m}^{r}($S)}{V_{g}^{f}(S)}}={\cfrac {K_{B}K_{v}/D_{m}}{\left(t_{g}^{f}s+1\right)\left(t_{m}s+{\frac {K_{m}}{D_{m}}}\right)}}} ^[7]

with the constants defined as below:

${\displaystyle K_{B}={\frac {G_{m}^{f}aV_{m}^{f}}{R_{m}^{f}(R_{g}^{a}+R_{m}^{a})}}}$

${\displaystyle K_{v}={\frac {G_{g}^{f}aW_{g}^{r}}{R_{g}^{f}}}}$

${\displaystyle t_{m}={\frac {J_{m}}{D_{m}}}}$

${\displaystyle t_{g}^{f}={\frac {L_{g}^{f}}{R_{g}^{f}}}}$

${\displaystyle K_{m}=D_{m}+K_{B}^{2}(R_{g}^{a}+R_{m}^{a})}$

See also[edit]

References[edit]

Citations

General references

• The Editors (Nov 1989). "Technology for Electrical Components". Power Transmission Design: 25–27. {{cite journal}}: |last= has generic name (help)
• Ward Leonard, H. (1896). "Volts versus ohms - the speed regulation of electric motors". AIEE Trans. 13: 375–384.
• Gottlieb, I.M. (1994). "Electric Motors & Control Techniques 2nd Edition". TAB Books. {{cite journal}}: Cite journal requires |journal= (help)
• Malcolm Barnes (2003). Practical Variable Speed Drives and Power Electronics. Oxford: Newnes. pp. 20–21. ISBN 978-0-7506-5808-9.